![]() To purchase a Threaded Tank, you'd need both a new ValveĪnd a new Tank to use with it ( saving the Media in the tank, and re-using the Brine Tank ). If you have this LEAK in your TANK you don't have a lot of options. Unfortunately the replacement tank of this design is no longer sold or manufactured. The UNIFLEX tank is a proprietary design used in Newer MacClean, Water Factory, CUNO and Aqua-Pure® softenersĪnd treatment systems ( bought out by CUNO, which in turn was bought out by 3M ). This system also saves water by metering use and regenerating only when necessary. Helps protect the entire plumbing system. Benefits include brighter clothing, cleaner dishes, less detergent consumption and less water usage. O-ring - Adapter Uniflex Cuno MacClean ORG-234 3M Aqua-Pure CS1001 - CS1001 Water Softeners - The Aqua-Pure CS Series Water Softener includes a heavy-duty lead-free brass valve. If you think you only need an O-ring, then go to this product we sell: I say "might" because we have seen ( received reports and photos from people who had ) a hairline crack in the TANK Lip that turned out to be the cause of the problem. Then yes, we have the o-ring that "Might" solve the problem. ** If the leak is due to the Adapter O-ring used with these proprietary clamp on tank adapters ( We Do Not have the Adapter or the Clamps ), If you don't offer replacement tank, is there another source? Want to replace a Uniflex Components D08040F tank. Removing the 155 or 255 Upper Valve Body Module.Repair Sears, North Star, GE SmartWater.Sears,North Star, Whirlpool, GE Smartwater, Mortons.O-ring # 31 ( not shown ) = 10381 = Bottom to TankĬross Reference ( but not limited to these models in the CEC 1000 Series ),Īnd Backwash Only ( no brine valve - no injector housing on Valve ),Īnd this next photo shows an older electronic version that used standard threaded tanks. O-ring # 29 = 11208 = Seal between the Valve and Adapter We can only provide 60121, but it will give you new seals and some new spacer to complete repair of your MacClean.Īnd this is a partial list of models that can use the 60090 piston ( F ) and the 60121 Seal Kit ( E, minus end spacer ) we offer ( noting we don't have the large extra spacer in our kits ). That is why they call their Kit 60121-C ( proprietary version with that special wider spacer made for MacClean valves ). ![]() You must "re-use" their larger spacer and not the small white end spacer that comes in the 60121 kit. MacCLEAN Model CWS100ME MCWS100ME CWS150ME CWS200ME CWS300ME CWS100MEJ CWS150MEJ CWS200MEJ CWS300MEJ CWS100MECJ CWS150MECJ CWS200MECJ CWS300MECJ Softener 1.0 cu ft Intellis, SpaceMaker Softener 1.0 cu ft Spacemaker Softener 1.0 cu ft, Black Jacket. The picture of the Seal Kit in the Fleck parts list shows a short spacer (part # 10757) as part of the Seals and Spacer Kit (part # 60121), however the Spacer in the MacClean Control valve is approx 1.5” long – any comments? Note the "collar" used to "clamp on" to proprietary Tank ( which we also can not provide ).Ībove is the newer Uniflex Tank ( no threads ) that is proprietary.īelow are an old MacClean ( such as the CS1001 and CEC1000 series ) that uses the same Pistons and Seals as the Fleck 2500 Here are photos of the newer Proprietary version MacClean that we can NOT provide any parts for. Prior years used either Fleck 5600 ( RS, NS, NLS or NSM models ) or Fleck 2500 ( CSM models )type valves, and most parts under the Fleck repair parts category should match up.Ĭheck part numbers, and email us with PHOTOS, if you are not SURE about your MacClean Valve and parts identification. The MacClean valves and tank are proprietary in design after 2001 ( bought out by CUNO, which in turn was bought out by 3M ).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |